| Produce CRB30025 Crossed Roller Bearing,CRB30025 Bearing Size 300X360X25mm | Basic Static Radial Load Rating Co:228000 N; d:160.000 mm; Basic Dynamic Radial Load Rating C:183000 N; Fillet Radius ra:2.00 mm; Fillet Radius rb:1.00 mm; Oil Speed Rating n2:3000 rpm; Grease Speed Rating n1:2500 rpm; B:40.00 mm; D:250.0000 mm; |
| RE 45025 UU Crossed Roller Bearing 450x500x25mm | Calculation factor Y0:2; T:600 mm; D:815 mm; Thrust factor K:1.74; B:600 mm; r3,4 min.:6 mm; Basic static load rating C0:31000 kN; d:625 mm; Comparative axial load rating CFa:468 kN; Mass bearing:768 kg; |
| 112.25.560 Slewing Bearing | Basic Static Radial Load Rating Co:65500 N; Basic Dynamic Radial Load Rating C:67100 N; d:40.000 mm; B:39.70 mm; D:90.0000 mm; Grease Speed Rating n1:5000 rpm; Accessories:Two Seals & Snap-Rin; Oil Speed Rating n2:6700 rpm; Fillet Radius ra:1.50 mm; Sealed Speed Rating n3:5000 rpm; |
| 25 mm x 52 mm x 15 mm Slewing Ring For Excavator HITACHI ZX225US, Part Number:9196732 | Da:289.999 mm; Taconite seal:TER 131; N1:28.575 mm; Stabilizing ring:SR-32-0; J min.:441.325 mm; A2:288.925 mm; H:336.55 mm; Cap bolt recommended tightening torque:203.4 N·m; Initial grease fill:793.8 g; Ca:113.817 mm; Size (mm):25 mm x 52 mm x 15 mm ; |
| 230.20.0600.503 Four Contact Ball Slewing Ring 534x748x56mm | Oil:4 200 min-1; dynamic Cr:46.370 kN; Grease:3 200 min-1; static Cor:113.000 kN; Pu:5.140 kN; D1:62 mm; D:85 mm; d:60 mm; rs (min):1 mm; H:17 mm; |
| VSI 200844-N Four Point Contact Slewing Ring | Oil:4 200 min-1; Static (Cor):92.600 kN; Da:169 max; Grease:3 500 min-1; ra:2 max; Dynamic (Cr):123.000 kN; Weight:3.13 kg; da:112 min; B:34 mm; Pu:3.557 kN; |
| A12-48E12 Four Point Contact Ball Slewing Bearing With External Gear | r1 min.:1 mm; Design (sliding contact surface combination):Steel/steel; b1:5 mm; Specific static load factor K0:300 N/mm²; α:8 °; Material constant KM:330; C:28.575 mm; ra max.:1 mm; D:61.913 mm; b:4.8 mm; |
| L6-25P9Z Four-point Contact Ball Slewing Bearings | Stabilizing ring:2 x 38151-38; J max.:488.95 mm; End plug (suffix Y):EPR 21; P150°:78.3 kN; P180°:94.3 kN; PG:1/4 NPT; N1:28.575 mm; Pa:40 kN; Cap bolt, SAE grade:5; Ca:89.789 mm; |
| M7-39P1 Angular Contact Ball Slewing Rings | Basic Static Radial Load Rating Co:710000 N; B:78.00 mm; Fillet Radius rb:1.50 mm; D:400.0000 mm; Fillet Radius ra:4.00 mm; Basic Dynamic Radial Load Rating C:507000 N; Grease Speed Rating n1:1600 rpm; d:190.000 mm; Oil Speed Rating n2:1900 rpm; |
| 1167/700 Bearing 700x900x36mm | Bolt Pattern D:2 3/4 in; Bolt Pattern E:23 1/2 in; Frame Accepts These Shaft Sizes (Bearing Bore):40 mm; Bolt Pattern C:0.55 in; Shaft C/L Distance F:1 31/32 in; Frame Size B:25 in; Frame Size A:5 1/4 in; Height G:3.938 in; Travel:18; |